Make a cheer spirit stick with a name on it
A spirit stick is the squad’s noisemaker and mascot rolled into one: a short stick with pom-poms on the ends, waved from the sideline and passed from hand to hand. This one carries a cheerleader’s name, printed in two colors and clipped on so it stays put through every stunt. Watch the five-minute build, or follow the steps below. Each one jumps to its moment in the video.
What you’ll need
Printed, free from here
- The cut-out name sign, printed in two colors
- Two sign holders sized to your dowel
Tools
- A 3D printer and two colors of filament
- A drill with a small bit
- Scissors
From the craft store
- A 1/2 inch wooden dowel
- Two pom-poms in your squad’s colors
- Rope for the handle
- Super glue
- Small zip ties
Another size works too. Buy it first, then size the holders to match.
Step by step
The finished spirit stick
Here’s where you’re headed: a name sign riding on a wooden stick, a pom-pom bursting from each end, and a rope handle to carry it by.
▶ Watch from 0:00Glue the clips to the back of the sign
Lay the sign face down. Put a few drops of super glue on the flat side of each holder and press one on toward each end of the name, with both rings in a straight line so the stick can pass through them together. Hold each one still for a few seconds, then leave the glue to set while you work on the stick.
▶ Watch from 0:05Measure and mark the dowel
Measure the same distance in from each end of the dowel and mark both spots. Matching marks keep the handle even, and leaving some wood past each mark keeps the end from splitting when you drill.
▶ Watch from 0:45Drill through the ends of the dowel
Drill straight through at each mark with a small bit, just wide enough for your rope. Drill both holes in the same direction so the handle doesn’t twist, and ease off as the bit breaks through the far side to keep the wood from splintering.
▶ Watch from 1:30Thread the cord through and glue it
Feed the rope through one hole, along the stick, and out the other, leaving enough slack between them for a hand to fit. A drop of super glue where the rope meets the wood holds it in place. If the cut end frays, a little glue on the tip stiffens it so it threads easily.
▶ Watch from 2:25Tie on the first pom-pom
Gather the pom-pom around one end of the dowel and cinch it with a small zip tie. Pull it as tight as it goes so the pom-pom can’t spin or slide off mid-cheer, then snip off the zip tie’s tail.
▶ Watch from 3:25Tie on the second pom-pom and trim
Do the same at the other end. Trim any strands that hang longer than the rest, then shake both pom-poms out and separate the strands with your fingers until they’re full and round.
▶ Watch from 4:25Snap the name sign onto the stick
Line the holders up with the stretch of stick between the pom-poms and press until both click on.
▶ Watch from 5:10All done
It’s ready for the sideline. Because the sign only clips on, it can come off for the ride home and go back on at the next game.
▶ Watch from 5:20
Printing the sign in two colors
The cut-out sign is a base trimmed to the shape of the letters, with the letters standing on top. The base prints in your first color and the letters in the second, so there’s exactly one filament swap, at a height your download tells you. A filament changer makes the swap by itself. On a one-spool printer, add a pause at that layer and load the second color when it stops.
Pick colors that match the pom-poms. A light base under dark letters reads best from the bleachers, like the blue on white in the video. A spirit stick gets shaken hard, so if you choose a thin script font, turn up Border to give the letters a wider base underneath, and keep the sign shorter than the stretch of stick between the pom-poms.
Why clips instead of gluing the sign to the stick
- A flat sign touches a round dowel along one thin line, so glue there has almost nothing to hold, and a good shake pops it loose. Each holder has a flat face that meets the back of the sign all the way across, so the glue holds on every bit of it.
- The holder’s ring grips the stick by snapping around it. No glue touches the wood, so the sign comes off whenever you want: for packing the stick flat in a bag, or for putting a new name on it when the stick is handed down to next year’s squad.
- Two holders, one near each end of the name, keep the sign from rolling around the stick.
Get the holder free: choose a dowel or PVC size, or type in your own measurement.
One for every cheerleader
- Open the cut-out sign, type the first name, and paste the rest of the roster into Make a set, one name per line. Up to 31 signs come down in one download, all with the same letter height, so they match when the squad lines up.
- Download the holder as many times as you like: print two per athlete and fill a whole plate at once.
- Work like an assembly line: mark one dowel, use it as the pattern for the rest, and drill them all in one go. Glue every pair of holders while the glue bottle is open.
- They make a great team night project, a banquet gift, or a surprise in each bag before a big competition.
Looking for more squad gear? The sports page has bag tags for every player and a name megaphone for cheer. Making sticks for the band? The band spirit stick puts music notes or an instrument over the name, and the color guard one has crossed flags.
Good to know
- What size dowel should I buy?
- The video uses a 1/2 inch dowel, which is also the size the holder starts at. Another size works too: measure the one you buy and enter it when you make the holder, so it clicks on snugly.
- Can I use PVC pipe instead of wood?
- Yes. The holder comes in PVC sizes too, and pipe drills just as easily.
- Are the sign and the holder both free?
- Both are. Sign in with Google to download them.
