Every file here is free to download, and you can add your own logo.

Anycubic Slicer Next: add a pause and swap filament colors

Slice in Anycubic Slicer Next, scroll Preview to where color two begins, then use the + handle menu to Add Pause and slice again. Your Kobra waits there.

Good for: Kobra S1 and Kobra 3 from Anycubic, without an ACE Pro. Menus match Anycubic Slicer Next 1.3 and later (September 2026).

Setting the pause in Anycubic Slicer Next

  1. 1

    Slice the plate

    In Anycubic Slicer Next, click Slice plate. The Preview tab opens with the layer slider standing along the right.

  2. 2

    Move up to color two

    Raise the slider's top handle to the first layer that holds nothing but the second color; on a name keychain, that's the first layer of letters. The handle shows the layer number and height in mm.

  3. 3

    Add the pause

    Right-click the + beside the handle and choose Add Pause. A marker shows the spot, and your Kobra will stop just before that layer.

  4. 4

    Slice and send

    Slice the plate again so the pause is in the file, then send it to the Kobra or save it.

Which layer, though? The first one in the new color. Here's how to spot it.

Your printer's stop command

The Kobra profiles have this covered. The Kobra 3 also accepts M600, which you can put in with Add Custom G-code in place of Add Pause.

Kobra 3, Kobra S1M601

When the printer stops

Load your first color and start the print. Once it reaches the pause:

  1. 5

    The printer stops

    It wraps up the layer underneath and waits for you.

  2. 6

    Switch colors

    From the filament menu on the screen, unload the first color and load the second. Purge until no old color shows.

  3. 7

    Pick up where it left off

    Lift the purged string away, keeping clear of the print, and confirm on the screen to keep going.

Changed your mind? Taking the pause out

Return the handle to the marked layer and click the small ×, or right-click it for Delete Pause. Slice again before printing.

Things that trip people up

  • Pauses need Anycubic Slicer Next 1.3.1 or newer.
  • Running an ACE Pro? No pause needed: assign a filament to each part and the ACE Pro handles the change.
  • If the right-click menu won't let you add a pause, the plate is probably printing By object. Set the print sequence to By layer in the process settings.
  • Pausing on layer 1, 2, or 3 is asking for trouble: the thin first layers can cool on the bed during the wait and peel at a corner.

What a Kobra does while it waits

Since Kobra 3 firmware V2.3.5.3, the hotend cools to 140 °C whenever a print is paused, to stop oozing and keep filament from baking in the nozzle. The strand won’t move until you heat up again.

Later firmware lets you feed and retract from the screen during a single-color pause (Kobra 3 V2.3.9.3, Kobra S1 V2.5.2.2). Newer still, you can jog the axes while paused (Kobra 3 V2.4.4.7, Kobra S1 V2.5.9.9), which helps when the head sits somewhere awkward to reach.

The Kobra 3 purges into a wiper at the far right of the gantry. If plastic lands beside it instead, Anycubic says to check that the wiper rebounds when you pull it and that its magnet catches the head.

Check the firmware before the first pause

A Kobra 3 lists its version under Settings → Device Informations → Printer Information. On a Kobra S1 it’s Settings → Device → Printer information. Either screen offers the update when a newer one is out.

Turn off LAN mode before you update. Anycubic’s updates need the printer bound to the app, and LAN mode blocks them.

Two Kobra 3 fixes matter for pauses: V2.4.0 stopped it extruding while paused, and V2.4.6.4 corrected where it purges when you resume.

Quick answers

Can I use M600 on a Kobra 3 instead of a plain pause?
Yes. Anycubic lists both M600 and M601 as supported on the Kobra 3. Add Pause writes M601. To get M600, open the right-click menu on the slider handle, pick Add Custom G-code, then type M600 in the box.
Why won’t the filament budge on my paused Kobra 3?
A paused Kobra 3 drops its hotend to 140 °C, which is too cool to move filament. Heat the nozzle to your filament’s printing temperature from the screen, then unload and load.
Can one Kobra 3 print use both M600 and M601?
Yes. Anycubic says the two can go on different layers of the same model. Use Add Pause (M601) for one swap and Add Custom G-code with M600 for another. Type M600 in capitals.